คุณยังไม่มีสินค้าในรถเข็น

คุณยังไม่มีสินค้าในรถเข็น

สินค้าทั้งหมด

สินค้าทั้งหมด

ตั้งค่าเป็นเรียงจากน้อยไปมาก

ตาราง รายการ

ต่อหน้า
  • BIBKO ADD-ON SAND AND GRAVEL SEPARATION

    A robust and easy to install separator divides the recycled aggregates into sand and gravel.

    0 บาท
  • BIBKO ADD-ON EXTERNAL BUCKET ELEVATOR

    A ComTec machine equipped with an external row of buckets. This compact solution lifts the waste from washing out concrete pumps or the batching plant into the ComTec without placing the machine below ground level. The external buckets are mounted on an extension of the main shaft of the machine.

    0 บาท
  • BIBKO ADD-ON DISCHARGE BUFFER AND PUMP DISCHARGE

    The advantage of a dosing buffer derives from the possibility to discharge several trucks at higher speed.

    The dosing buffer collects the residual material and continuously feeds it into the connected recycling machine.

    The produced washing quality as well as the separation cut of the fines contained in the greywater is assured as they are independent of the evacuation speed of the trucks. Due to the higher discharge speed of the trucks the total time for the discharge and wash process of the trucks is significantly reduced.

    0 บาท
  • BIBKO FILTER PRESS SOLUTIONS

    - Purification of residual/wash water with fine particles
    - Purification of coloured water
    - Simple handling of the filter cake
    - Little space required, high filtration performance of the system
    - Low operating and maintenance costs

    0 บาท
  • BIBKO COMTEC RECYCLING SYSTEMS

    - Recycling capacity of 4, 10, 20 and 30 m³/h
    - Dosing buffer and a special extension allow for fast discharge into the machine
    - Large capacity wash drum (0.5-3.5 m³) guarantees best performance
    - Compact design. No foundation mobile option available.
    - Light aluminium cover supported by gas pressure springs
    - Heated option available
    - Hot-dip galvanised for longevity

    0 บาท
  • BIBKO RWS RECYCLING SYSTEMS

    - Recycling capacity of 4, 8, 12 and 18 m³/h
    - Compact design. No foundation mobile option available.
    - Heated option available
    - Hot-dip galvanised for longevity

    0 บาท
  • เครื่องบากขอบลบคมแผ่นเหล็ก ท่อเหล็ก OMCA รุ่น Art.760/3

    BEVEL LENGTH (L): max 22 mm

    BEVEL ANGLE: 15° - 60° (*)0°-60°

    0 บาท
  • เครื่องบากเหล็กแผ่นอัตโนมัติ OMCA art. 930 Reverse

    Machine a reverse downside chamfer with an angle of 0° to 60°, or a square edge condition a plate up to 100 mm thick at an automatic feed speed of up to 1.4 meters/minute.

    Motor Power
    230/400 Volt, 3 Phase
    5,5KW.( 5500W) 50/60 HZ

    Bevel Length
    max 59 mm

    Bevel Angle
    0° – 60°

    Plate Thickness
    8 – 60 mm (*) 8 – 100 mm

    Feeding Speed
    0 -1.4 mt/min

    0 บาท
  • เครื่องบากเหล็กแผ่นอัตโนมัติ OMCA art. 900 Big Plus

    Faster machining and longer insert life is the benchmark of this machine. This rigid and durable unit has the highest cutter motor power at 5.5 kW.  The four feeding wheels and machine design make this one of the most rigid machines on the market.

    Motor Power
    230/400 Volt, 3 Phase
    5,5KW.( 5500W) 50/60 HZ

    Bevel Length
    max 77 mm

    Bevel Angle
    15° – 80° (*) 0°-80°

    Plate Thickness
    8 – 100mm (*) 8- 200 mm

    Feeding Speed
    0 -1.4 mt/min

    0 บาท
  • เครื่องบากเหล็กแผ่นอัตโนมัติ OMCA art. 900 Plus

    Machine a bevel in a metal plate with a chamfer angle of 15° to 80° at a linear travel speed of up to 1.4 meter/minute. The standard model ART.900 Plus machine will bevel plates with a thickness from 8 mm to 60 mm, with options to bevel a thickness less than 8 mm, or 8 mm to 200 mm. 

    Motor Power
    230/400 Volt, 3 Phase
    4kw (4000W), 50/60 Hz

    Bevel Length
    max 55 mm

    Bevel Angle
    15° – 80°

    Plate Thickness
    8 mm – 60 mm (*) 8 mm – 100 mm

    Feeding Speed
    0 -1.4 mt/min

    0 บาท
  • เครื่องบากเหล็กแผ่นอัตโนมัติ OMCA art. 900

    Machine a V bevel in a plate up to 200 mm thick for butt welding or edge conditioning with a chamfer angle of 15° to 60° at a automatic feed speed of up to 1.4 meters/minute.  The rigid frame incorporates steel where required and aluminum casting where permissible to optimize strength and ergonomics. The motorized feeding process is achieved over hardened work plates with sliding rollers, all driven by two 90 shore polyurethane wheels. 

    Motor Power
    230/400 Volt, 3 Phase
    4kw (4000W), 50/60 Hz

    Bevel Length
    max 55 mm

    Bevel Angle
    15° – 60°

    Plate Thickness
    8 mm – 60 mm (*) 8 mm – 100 mm / 8 mm – 200 mm

    Pipe
    Ø min 3000 mm

    Feeding Speed
    0 -1.4 mt/min

    0 บาท
ตั้งค่าเป็นเรียงจากน้อยไปมาก

ตาราง รายการ

ต่อหน้า
expand_less